A basement finish is the one home project where the electrician and the general contractor are formally separate parties. In Firestone the Town’s fee schedule lists basement finish as a plan-review permit category, and the contractor licensing table treats the basement-finishing contractor and the electrician as two different licences. That split is not bureaucracy — it is the reason the rough-in inspection can stop a drywall crew in its tracks. Precision Service Electric wires basement finishes in Firestone. Call 970-593-3190.

What Basement Electrical Work Actually Includes
The scope runs from circuit design through trim-out: lighting layout and switching, general receptacles, dedicated circuits for a freezer, fitness equipment, a media room or a home office, smoke and carbon-monoxide interconnection, and the panel work that makes any of it possible.
It is a design exercise as much as a wiring one. Two bedrooms and a bath is a different circuit plan from a single open rec room, and a theatre wall with a projector changes where the boxes go. That is why the walkthrough happens with the household rather than only with the framer.
Why a Finish Is Its Own Project
A service call fixes something that exists. A basement finish creates circuits that did not, inside walls that do not yet exist, on a schedule shared with three other trades. The electrical work has two distinct phases and an inspection between them, and the inspection is what forces the sequence.
Rough-in is everything that lives behind the drywall: boxes at the right height, cable drilled and protected where it passes through framing, dedicated circuits where equipment needs them, and switch legs that decide which door turns on which light. Trim-out is devices, fixtures, covers and the panel work. Between them sit insulation, drywall, tape and paint, and none of that can proceed over an uninspected rough-in.
Code Requirements a Firestone Basement Must Meet
Arc-fault protection is required on the branch circuits the code specifies for dwelling areas, and ground-fault protection is required for receptacles in the locations the code lists — in a basement that includes finished rooms, not only the unfinished utility half. Receptacles in the locations the code lists must be tamper-resistant, subject to its exceptions, and bedrooms need compliant lighting alongside the emergency escape and rescue opening.
Smoke and carbon-monoxide alarms have to be installed and interconnected where the applicable code requires it, including its exceptions for existing homes; in a finished basement that usually means a device on the existing system rather than a standalone unit on the ceiling. The breaker count this produces is higher than homeowners expect, and it belongs in the estimate rather than in a change order.
Your Panel and the New Circuits
A finished basement typically adds eight to fifteen circuits. In a newer Firestone house the panel may already be carrying a heat pump and an EV charger, and the honest answer is sometimes a subpanel rather than forcing tandems into a full panel.
A subpanel adds spaces; it does not add capacity. Whether the service can carry the additional load is a calculation — the same arithmetic a panel replacement starts from — and if the service is the real limit, the two jobs are planned together rather than one after the other.
Permits in Firestone
Basement finish and remodel sit on the Town’s list of permits that require plan review, and electrical changes are permitted work in their own right. Applications run through the Building Division at 9950 Park Avenue, 303-833-3291, via the CitizenServe portal, and the Town performs its inspections in house under the 2023 National Electrical Code.
The licensing split is the detail worth understanding. A basement-finishing contractor holds a Class B licence, which carries an annual fee. Electricians hold a separate no-fee licence that requires proof of state licensure and a certificate of insurance naming the Town as certificate holder and additional insured, renewed annually. Two licences cover two scopes, and the Town verifies the electrician’s licence and lists the contractors on the permit application.
The fire district stays out of it: the Frederick-Firestone Fire Protection District’s fee schedule states that its permits are not required to construct, remodel or renovate one- or two-family homes or townhomes.
Working With Your General Contractor
The GC owns framing, insulation, drywall, paint and trim; we own the electrical permit, the rough-in, the trim-out and the inspection. That division works when the electrical is sequenced deliberately and badly when it is treated as a trade that arrives at the end.
We work directly with GCs on Firestone finishes and with homeowners acting as their own contractor. In the second case we are explicit about the sequence: which permit is whose, when the rough-in inspection is called, and why the drywall date depends on it.

Our Process
Plan and layout review with the household and the GC, then circuit and load design, then the Town permit and plan review, rough-in, the rough-in inspection, insulation and drywall, trim-out, the final inspection, and finally labelling written the way the homeowner will read it.
What Moves the Price
Square footage is the headline, but the drivers are circuit count, whether a bathroom or kitchenette is involved, whether a subpanel is needed, whether the ceiling is open or finished, whether there is a shop with 240-volt equipment, and how much of the ceiling assembly is accessible. A bedroom-and-bath finish and a media suite with a wet bar are different orders of magnitude.
We quote the electrical scope on its own line so it can be compared with another electrician’s number directly rather than buried in a general contractor’s lump sum.
Related Work in Firestone
If the basement is where the car will charge, the Firestone EV charger page covers that circuit. If the panel is the constraint, start with panel replacement in Firestone. Ceiling work usually brings lighting with it — see lighting upgrades in Firestone — and for another town’s version of the same job, read basement electrical finishes in Longmont or our service area.


“Jordan was prompt and friendly in addressing my concern and got Mitch to my home within 1 week to add the new outlets we were needing. Mitch was a complete delight to work with: he thoroughly explained the process, was kind and gracious and cleaned up after himself as he left. I would HIGHLY recommend this company to anyone needing electrical work! They were a dream to work with! THANK YOU!”
Frequently Asked Questions
Do I need a permit to finish my Firestone basement?
Yes. Basement finish is a plan-review permit category in Firestone, and the Building Division confirms how the electrical work is included in the permit application.
Which licence does the electrician need?
The Town’s no-fee electrician licence, with proof of state licensure and a certificate of insurance naming Firestone as certificate holder and additional insured. It is a different row from the Class B licence a basement-finishing contractor holds.
How many inspections will there be?
Typically a rough-in inspection before insulation and drywall, and a final after devices and fixtures. The Town may require additional inspections depending on scope, and the building side has its own.
Can I add a bathroom and a wet bar?
Yes. A bathroom generally needs a 20-amp receptacle circuit, and the bar’s receptacles and appliances need supply and protection as the code requires. Both get planned before the framing is closed.
My panel is full — do I need a service upgrade?
Not necessarily. A subpanel adds spaces; whether the service has capacity is a separate calculation. United Power, the co-operative that supplies Firestone, would handle any service-side change.
Can the general contractor pull the electrical permit?
The electrician performing the work has to be properly licensed and listed on the permit application; we confirm the permit arrangement for the project with the Building Division, and that arrangement is what the rough-in date depends on.
Request a Basement Electrical Quote in Firestone
A floor plan, even a hand sketch, plus a photo of the open panel is enough to start. Precision Service Electric is family owned, in business 30 years, licensed and insured under Colorado license #3918, factory-trained and an authorized Generac dealer, and rated 4.8 stars across 47 Google reviews. Call 970-593-3190 or request a quote.