Wellington is one of the few Front Range towns where the charger conversation starts with the co-operative rather than the city utility. If your address is on Poudre Valley REA, the rebate tiers and the smart-charging programme are specific and worth reading before you buy hardware; if it is on Xcel, the path is different. Precision Service Electric installs Level 2 chargers in Wellington and files the Town permit as part of the job. Call 970-593-3190.

Level 1 vs Level 2: What Wellington Drivers Actually Need
The cord that came with the car is a Level 1 charger, and it adds roughly three to five miles of range per hour on a standard 120-volt receptacle. For a household that drives twenty miles a day and parks overnight, that is genuinely enough — and saying so is cheaper than selling a circuit.
Beyond that, a Level 2 circuit on 240 volts adds something in the range of twenty to thirty miles per hour, depending on the vehicle’s onboard charger. The decision is usually made by the commute: a daily round trip to Fort Collins or a weekly run to Denver changes the arithmetic quickly, and a second EV in the driveway changes it again.
Your Panel and the New Circuit
Charging current is not the same number as the breaker. Electric vehicle charging is treated as a continuous load, so the branch circuit is sized for at least 125% of the equipment’s applicable maximum continuous load: a unit configured for 48 amps needs a 60-amp breaker, a 40-amp unit needs 50, a 32-amp unit needs 40.
That chain — panel capacity, breaker, conductor size, charger setting — is the job. A 100-amp service already carrying electric heat and a range may have room for a charger set to 32 amps but not one set to 48, depending on the load calculation — and the honest answer is sometimes a lower-amperage install rather than a service upgrade. Wellington has plenty of both: older in-town houses on 100-amp services, and newer subdivisions where the panel is generous but the spaces are filling up.
PVREA Rebates for Wellington EV Chargers
Poudre Valley REA publishes member EV charger rebates: a Level 2 rebate of up to $250, split between installation and equipment, and a higher tier of up to $1,000 when the member enrols in the co-op’s DrivEV smart-charging rewards or a time-of-use rate. Programme rules require an electrician’s receipt and an application window that runs after the installation.
Terms and amounts change, so we point you at the co-op’s current page rather than quoting a figure from memory, and we do not file the rebate for you. What we do is make sure the invoice you submit carries what the programme asks for.
If Your Address Is on Xcel Instead
Wellington’s electricity is split: some addresses are Poudre Valley REA, others Xcel Energy. The charger work itself is identical, but the paperwork is not — the two utilities run their own programme structures, and a service upgrade on an Xcel address is coordinated through that company rather than the co-op.
The first thing we ask for is a photo of the bill, because it settles which provider and which programme apply in one look. The service rating and meter arrangement we check in person.
Permits in Wellington
Applications run through the Town of Wellington Building Department at 8225 Third Street, 970-821-5078, using Community Core, with plan review, permitting and inspection handled by SAFEbuilt’s Windsor branch on the Town’s behalf — the inspection line is 970-674-1036. The Town’s one-stop electrical categories cover electrical-only work, which is what a charger circuit is.
Any contractor working in Wellington needs a current Town of Wellington contractor licence before a permit can be applied for. The Town adopted the 2024 I-Codes effective 1 January 2026 and states alignment with the current NEC; we confirm the operative edition at permit time.

Our Process: Installation, Step by Step
A site visit and a load check first, then a written quote that names the circuit size and the charger setting. Then the permit, the installation — the run from the panel, conduit where the path is exposed, the mounted unit, the breaker — and the commissioning test with the car, followed by the inspection.
Most garage installs are one day. A detached garage, a long run across a finished basement, or a pedestal at the driveway edge adds scope, and we walk the route before quoting rather than after the conduit is on the wall.
EV Charger Installation Cost in Wellington
No Wellington-specific survey is published. The nearest attributable figure is Three Crowns Electric’s Northern Colorado range for an EV charger installation: $800 to $2,500 for the installation, with hardware separate at $400 to $1,200. Those are that company’s published numbers rather than ours, and a long run or a service upgrade sits outside them.
What moves the number here: distance and difficulty of the run, whether the panel has capacity and spaces, whether a subpanel is needed, whether the unit is hardwired or on a receptacle, and whether the permit requires anything beyond the one-stop electrical category.
Charging at Home vs Wellington’s Public Stations
Wellington has public fast charging in town — ChargeHub lists a ChargePoint station at the Maverik on 6th Street with DC fast charging at about $0.45 per kWh — and it is worth knowing about for a top-up on a long day. It is not a substitute for home charging on cost or convenience: overnight charging at home is slower, cheaper per mile, and does not require planning the week around a charger.
For a household that enrolled in PVREA’s time-of-use rate, the overnight window is also where the savings live, which is why the co-op pairs the rebate with the smart-charging programme.
Service Area: Wellington and Northern Colorado
We work Wellington, Fort Collins, Timnath, Windsor, Severance and the communities north of the city. The utility and the permitting authority change at the town line, which is why this page is specific to Wellington rather than regional.
Request an EV Charger Quote in Wellington
Send a photo of the open panel, a photo of the bill, and the wall where the charger will go. Precision Service Electric is family owned, in business 30 years, licensed and insured under Colorado license #3918, factory-trained and an authorized Generac dealer, and rated 4.8 stars across 47 Google reviews. Call 970-593-3190 or request a quote.
Related Work in Wellington
If the service turns out to be the constraint, the Wellington panel replacement page covers the arithmetic and the Town’s permit categories. For the same work elsewhere, read the Loveland EV charger page or the Longmont page, or browse our service area.


“Excellent experience from Bid to Completion. Thoroughly explained what to expect and the job was completed quickly and correctly. Hole cut, new box and wiring. Guys were professional and were happy with the results!”
Frequently Asked Questions
Do I need a permit to install an EV charger in Wellington?
Yes. A new 240-volt circuit is electrical work, applied for through the Town Building Department via Community Core and inspected by SAFEbuilt.
What rebates are available in Wellington?
If your address is on Poudre Valley REA, its published programme includes a Level 2 charger rebate and a higher tier for members enrolled in DrivEV or a time-of-use rate. Xcel addresses follow that company’s own programmes.
How do I know which utility serves my house?
Your bill. Wellington is split between Poudre Valley REA and Xcel Energy depending on the address, sometimes street by street.
Will my panel carry a 48-amp charger?
That is what the load calculation decides. On a 100-amp service with electric heat, a lower charging setting may be what fits; on a newer 200-amp service with gas appliances there is usually more room. The load calculation decides, and the circuit follows from the equipment’s setting.
How long does the installation take?
A straightforward garage install is often one day. Long runs, a detached structure or a service upgrade extend it, and the inspection depends on SAFEbuilt’s schedule.
Can you install a charger I bought myself?
Yes, provided the unit is listed for the application and its settings match the circuit we install. We check the equipment against the circuit before the permit goes in.